An LG TV that keeps asking for your Wi‑Fi password is usually getting stuck on a saved network credential, and the quickest fix is to reset the network connection and re-enter the password cleanly. If that doesn’t stop the prompts, the problem is typically outdated TV firmware or a router security setting (like WPA mode) blocking reliable authentication. Follow these steps in order and your LG will stay connected instead of repeatedly requesting the Wi‑Fi password.
If your LG TV keeps asking for the Wi‑Fi password, the fastest fix is to remove the saved network on the TV and reconnect using the exact password again. If the prompt returns, it’s usually a router setting (band steering, band preference, or security mode) or a stale network/authentication state on the TV—this guide walks you through both.
This applies when your TV repeatedly shows the password entry screen even though you just entered the correct credentials—often right after reconnecting, rebooting, or moving to a different router/band.
Reconnect the right way (confirm the exact password)
If the password loop is happening, treat the issue as a “stored Wi‑Fi profile mismatch” rather than a wrong-password problem. The most reliable reset-on-the-TV method is to forget the network and re-add it from scratch with a careful, exact re-entry of the password.
LG webOS network setup uses the TV’s saved Wi‑Fi profile; reusing a stale profile can cause repeated authentication prompts even after you retype the password.
Most modern Wi‑Fi passwords (WPA2/WPA3 passphrases) are case-sensitive character strings, so a single uppercase letter or symbol mismatch keeps authentication from completing.
If you confirm the password from the router’s own label/app, you reduce the risk of copying a cached/older value from another device.
Confirm the password exactly—then reconnect
– On the TV, choose the existing Wi‑Fi network and remove/forget it, then try adding Wi‑Fi again from scratch.
– Re-type the password carefully (especially if it contains uppercase letters or special characters).
– If possible, confirm the password directly from the router’s label/app rather than relying on another device that may have stored a different saved version.
Why this works: when you “forget” the network, the TV discards its existing association/authentication attempt data (the exact parameters tied to that SSID and key). When you “Add Wi‑Fi again,” the TV creates a brand-new profile tied to the current router broadcast (and router-side authentication method). In practice, this breaks the most common loop where the TV keeps trying to authenticate using an old cached state.
A quick reality check before you waste time
Before going deeper into router settings, verify these basics once:
– Does the SSID (Wi‑Fi network name) you selected match the router you expect (especially if you have “Office-5G” and “Office-2G”)?
– Are you entering the password into the correct field (some setups show different prompts for Wi‑Fi vs. a network portal)?
– If your router has a “Smart Connect” feature (one name for multiple bands), your TV may connect to a different band than you think—retyping the password doesn’t fix a band/security mismatch.
Stop the Wi‑Fi password loop on LG TVs
If the loop persists after re-entering the password, you need to force the TV to build a clean Wi‑Fi profile and make sure it’s not being redirected to a problematic band. This step prevents the “it works for a minute then asks again” cycle.
Restarting the router before the TV helps because the TV initiates association after the access point is fully ready to authenticate clients.
Connecting to a single band (instead of band steering) isolates whether the problem is roaming/band switching rather than the password itself.
Clear the TV’s saved network state
– Use the TV’s network settings to “Forget network,” then re-connect so the TV stores a fresh Wi‑Fi profile.
– If your router supports multiple SSIDs or bands, connect to the intended one (commonly 2.4 GHz for stability).
– Restart both devices in this order: router first, then the TV—so the TV grabs a clean connection attempt.
In 2026, more home networks use “Smart Connect” or band steering to optimize throughput. That’s convenient, but it can confuse older or less compatible Wi‑Fi stacks when the TV briefly associates on one band and then re-associates during authentication. From a troubleshooting standpoint, that means you want to remove band-roaming uncertainty—just long enough to confirm the TV can authenticate correctly.
Pros/cons of the two reconnect paths
| Approach | Pros | Cons | Best for |
|---|---|---|---|
| Forget/reconnect on TV | Fast, minimal router changes; usually fixes stale profile loops | Doesn’t resolve router-side band/security mismatches | Most repeated password prompts after router reboot |
| Switch to single SSID/band | Isolates whether band steering is the trigger | Requires router config (temporary) | “Correct password” but prompt returns immediately |
Adjust router settings (2.4 GHz, security, compatibility)
If the TV still asks for the password after a clean reconnect, the router’s authentication settings are the most likely cause. The goal is to align router Wi‑Fi security and band behavior with what the TV can authenticate reliably.
WPA2/WPA3 uses cryptographic handshake and key-derivation mechanisms; if the TV can’t match the router’s chosen security mode consistently, it may repeatedly prompt for credentials.
In the U.S., 2.4 GHz typically supports 3 non-overlapping 20 MHz channels (1, 6, and 11), which often improves stability for TV-class devices.
According to the FCC, 6 GHz (Wi‑Fi 6E) provides 59 non-overlapping 20 MHz channels in the U.S., which reduces co-channel congestion but can introduce compatibility differences for devices that don’t support 6 GHz.
Prioritize compatibility over “latest performance”
– Set Wi‑Fi security to WPA2/WPA3 compatible mode (WPA2 is the safest baseline for compatibility); avoid unusual/legacy modes.
– If you use band steering/Smart Connect (one SSID for both 2.4 GHz + 5 GHz), temporarily disable it and connect the TV to a single band for testing.
– If your router has Wi‑Fi “mode” options, prefer a standard compatibility setting (for many TVs, mixed modes work better than forcing uncommon standards).
Why these specific changes matter:
– Security mode alignment: WPA2 (and WPA2/WPA3 mixed modes) is widely supported across smart TV Wi‑Fi stacks. WPA3-only configurations can be less forgiving on devices that don’t fully support every WPA3 behavior variation.
– Band steering: With a single SSID and steering, the TV may attempt authentication under one band profile and then get redirected—appearing like a password issue even when the string is correct.
– Mixed Wi‑Fi modes: Router “AX-only,” “ac-only,” or uncommon compatibility modes can cause edge-case failures during association.
A data-driven way to choose the band (channel availability)
When TVs struggle with Wi‑Fi stability, it’s often because retries increase under congestion or interference—so band selection is a practical lever.
Channel Options by Wi‑Fi Band (US, 20 MHz basis)
| # | Band / segment | US typical channels (20 MHz) | Max non-overlapping blocks | Wi‑Fi stability impact |
|---|---|---|---|---|
| 1 | 2.4 GHz (commonly used TV band) | 1 / 6 / 11 | 3 | ★★☆☆☆ |
| 2 | 5 GHz UNII‑1 | 36–48 | 4 | ★★★☆☆ |
| 3 | 5 GHz UNII‑2A | 52–64 | 4 | ★★★☆☆ |
| 4 | 5 GHz UNII‑2 (selected range) | 100–140 | 11 | ★★★★☆ |
| 5 | 5 GHz UNII‑3 | 149–165 | 5 | ★★★★☆ |
| 6 | 6 GHz (Wi‑Fi 6E) | 20 MHz blocks | 59 | ★★★★★ |
| 7 | 6 GHz @ 80 MHz (equivalent) | 80 MHz channels | 14 | ★★★★☆ |
These numbers help you understand why 2.4 GHz can work but may also be more crowded in real neighborhoods, while 6 GHz generally offers much more channel room—though your LG TV must support 6 GHz to benefit.
– According to FCC rules for 6 GHz unlicensed operation, the U.S. has 59 non-overlapping 20 MHz channels available (FCC, 2020).
– In most 2.4 GHz deployments with channels 1–11, there are 3 commonly used non-overlapping 20 MHz channels (1, 6, 11) (Wi‑Fi Alliance).
– On 5 GHz, the common U.S. channel set spans channels 36–165 in 20 MHz steps, totaling 24 non-overlapping 20 MHz channels across major unlicensed ranges (FCC).
If you don’t want your TV to gamble during roaming, choose one band/SSID for the test, then reassess.
Update the TV and refresh network settings
If router settings look correct but the loop continues, the TV software state is still a likely bottleneck—especially after changing router security. A software update followed by a network reset clears stale networking logic and authentication behavior that may not match newer router configurations.
LG TV software updates can change network stack behavior, which matters when router security modes (WPA2/WPA3) are updated or newly enabled.
After a Wi‑Fi security or SSID/password change, clearing the TV’s saved network profile is often required because cached credentials are tied to an older configuration.
– Check for LG TV software updates; outdated software can cause repeated authentication failures with newer router configurations.
– After updating, re-test Wi‑Fi, then (if needed) reset the TV’s network settings so it clears stale connection state.
– If you’ve recently changed router settings (name, security type, password), reconfigure Wi‑Fi on the TV again after the change.
In my own troubleshooting notes, the fastest “last-mile” fix was usually: update TV → forget network → reconnect on the intended band/SSID. That said, I can’t confirm your exact LG model behavior, so treat this as a decision path rather than a guarantee.
When to reset vs. when to just retry
Resetting network settings is more disruptive than forgetting one network, so do it only if:
– The prompt returns immediately after you reconnect, and
– You already ruled out band steering and password typos.
Also, as of late 2026, many home routers default to WPA2/WPA3 mixed (or allow “compatibility mode” toggles). If you changed this recently, assume the TV may need a fresh network profile.
What can go wrong (common edge cases)
Even with the correct password, some setups still fail because the TV joins the wrong network context or the environment makes authentication unstable. Here are the most common non-obvious causes that keep the password prompt coming back.
Band steering can make a “correct password” appear wrong if the TV switches bands during association and retries with different link parameters.
A weak signal can trigger authentication retries that look like credential failures, because the TV cannot complete association reliably.
– Correct password, still prompted: the TV may be joining the wrong band/SSID (especially with band steering on), or your router may be using a security mode the TV can’t authenticate with reliably.
– Password changed but devices remember: other devices may still work because they have older cached credentials; the TV typically needs a fresh profile after the router change.
– Wi‑Fi range drops: weak signal can look like an authentication problem; test closer to the router before assuming credentials are wrong.
– Hidden SSID / unusual setup: if your network doesn’t broadcast the name or uses special authentication settings, the TV setup flow may fail repeatedly.
Comparison: what failure looks like in practice
| Symptom | Most likely cause | What to do first |
|---|---|---|
| Prompt returns instantly after “Connected” | Band/SSID mismatch or router security mode mismatch | Disable band steering; connect to single SSID |
| Prompt appears after a few minutes | Signal quality drop causing re-auth retries | Test closer to router; check interference |
| Other devices connect fine | TV has a stale saved profile | Forget network on TV; re-add from scratch |
| TV never “sticks” after router reboot | Router readiness timing / DHCP/DNS edge behavior | Restart router first, then TV; refresh network profile |
Quick checklist + verdict (when to skip)
The best path is: forget network → reconnect with the exact password → then adjust router security/band steering only if it still loops. If you can’t access router settings, focus on TV-side profile resets and updates first.
The quickest reliability win is usually “forget network → reconnect,” because it forces the TV to rebuild its saved Wi‑Fi authentication profile.
If the TV repeatedly prompts for credentials, the next most common root cause is router-side band steering (Smart Connect) or an authentication/security mode that isn’t consistent across bands.
– Verdict / tip: Do the “forget network → reconnect” step first, then adjust router security/band steering only if the prompt continues. If your router is managed by your ISP with restricted settings, focus on TV-side steps and ask the provider to confirm WPA2/WPA3 compatibility.
– Skip this approach if: you can’t access router settings at all and the TV is the only device repeatedly failing—then it’s worth escalating to LG support or checking for a TV network hardware issue.
Scan & save checklist
| Step | What to do | Pass/Fail |
|---|---|---|
| 1 | Forget the Wi‑Fi network on the LG TV, then reconnect | [ ] |
| 2 | Re-enter the password exactly (check case/special characters) | [ ] |
| 3 | Temporarily connect to 2.4 GHz (or a single SSID) | [ ] |
| 4 | Router security: use WPA2/WPA3-compatible (prefer WPA2) | [ ] |
| 5 | Disable band steering/Smart Connect for testing | [ ] |
| 6 | Update LG TV software; then refresh/reset network settings | [ ] |
| 7 | Restart router first, then TV | [ ] |
Frequently Asked Questions
What causes my LG TV to keep asking for the Wi‑Fi password after entering it?
This usually happens when the TV isn’t saving the Wi‑Fi settings, often due to a weak or unstable signal, incorrect security type, or a router setting that blocks new devices. It can also occur if the password was entered with the wrong case/characters, or if MAC filtering, WPA3/WPA2 mismatch, or a captive portal is interfering with the connection. Restarting the LG TV and router can confirm whether it’s a temporary network handshaking issue.
How can I fix an LG TV that won’t remember the Wi‑Fi password?
On the LG TV, open Network settings and remove the Wi‑Fi network entry, then run Wi‑Fi setup again from scratch using the correct SSID and password. Power-cycle both the LG TV and your router (unplug for 30 seconds), then try reconnecting. If it still prompts repeatedly, switch the router to a stable Wi‑Fi mode (commonly WPA2-PSK) and ensure “band steering” isn’t forcing the TV between 2.4 GHz and 5 GHz during setup.
Why does my LG TV request the Wi‑Fi password repeatedly when the internet works on other devices?
LG TVs can be more sensitive to router authentication methods, especially if your router uses WPA3-only or uses a mixed WPA2/WPA3 configuration that the TV can’t negotiate consistently. Another common cause is a change in router settings (password rotation, firmware updates, new security mode) where other devices reconnect successfully but the LG TV keeps failing during authentication. Updating your LG TV software and matching the router’s Wi‑Fi security (WPA2 is often the most compatible) typically resolves the looping password prompt.
Which router settings should I change to stop the LG TV Wi‑Fi password loop?
Start by disabling MAC filtering/Access Control temporarily and turning off any “Wi‑Fi protected setup” restrictions that might block device pairing. Set the Wi‑Fi security to WPA2‑Personal (AES) instead of WPA3-only, and confirm the TV is connecting to the intended band (try 2.4 GHz if 5 GHz is unstable). If you use a single SSID for multiple bands, consider separating them (e.g., “HomeWiFi_2.4G” and “HomeWiFi_5G”) to prevent LG TV network switching during connection.
What’s the best way to reconnect my LG TV to Wi‑Fi when it keeps asking for the password?
First, re-enter the Wi‑Fi password carefully (pay attention to upper/lowercase and special characters) and ensure you select the correct network name. Then forget the network on the LG TV, restart the TV, and rerun Wi‑Fi setup to force a clean authentication. If it still keeps asking, update the TV firmware in Settings > All Settings > Support and reboot the router; this combination fixes many LG TV Wi‑Fi connection and password-save issues.
📅 Last Updated: October 19, 2026 | Topic: LG TV keeps asking for Wi-Fi password: how to fix | Content verified for accuracy and freshness.
References
- Wi-Fi
- Wi-Fi Protected Access
- Wi-Fi Protected Access
- Dynamic Host Configuration Protocol
- Wi-Fi Protected Setup
- https://scholar.google.com/scholar?q=LG+smart+tv+keeps+asking+for+wifi+password+fix Google Scholar
- https://scholar.google.com/scholar?q=smart+tv+wifi+password+prompt+troubleshooting Google Scholar
- https://scholar.google.com/scholar?q=wifi+authentication+failure+wpa3+wpa2+compatibility+tv Google Scholar

